# DisableRealTimeData and EnableRealTimeData Commands

**URL:** <http://discussions.gridprotectionalliance.org/t/disablerealtimedata-and-enablerealtimedata-commands/1307>\
**Category:** openPDC\
**Created:** [September 10, 2024, 7:03pm UTC](http://discussions.gridprotectionalliance.org/t/disablerealtimedata-and-enablerealtimedata-commands/1307 "2024-09-10T19:03:00Z")\
**Posts on this page:** 3\
**Page:** 1

<div class="post-metadata">

**Author:** ![FlorianoTorres](http://discussions.gridprotectionalliance.org/letter_avatar_proxy/v4/letter/f/a5b964/32.png) [@FlorianoTorres](http://discussions.gridprotectionalliance.org/u/FlorianoTorres)\
**Post date:** [September 10, 2024, 7:03pm UTC](http://discussions.gridprotectionalliance.org/t/disablerealtimedata-and-enablerealtimedata-commands/1307/1 "2024-09-10T19:03:00Z")

</div>

Hi!

I’m in a integration process between OpenPDC and another PDC, and there are two commands - DisableRealTimeData and EnableRealTimeData - sent by this another PDC that stops the stream (DisableRealTimeData) and starts the stream (EnableRealTimeData), as we can see below:

 ![image](http://discussions.gridprotectionalliance.org/uploads/default/original/2X/e/ec85469320e9b5d739a7ef89af0da9caa8d3b3e6.png)

It follows the OpenPDC configuration:

 ![image](http://discussions.gridprotectionalliance.org/uploads/default/original/2X/f/f8bde186c3abb2b7741e4b04bb1674238959254a.png)

 ![image](http://discussions.gridprotectionalliance.org/uploads/default/original/2X/7/7f77e5abf2382b44622cbbe8411ff6b7ecbc2a3c.png)

Can you give some light above those commands and if there are any configuration for then in OpenPDC?

Thanks,

Flor.

---

<div class="post-metadata">

**Author:** ![StephenCWills](http://discussions.gridprotectionalliance.org/user_avatar/discussions.gridprotectionalliance.org/stephencwills/32/20_2.png) [@StephenCWills](http://discussions.gridprotectionalliance.org/u/StephenCWills)\
**Post date:** [September 10, 2024, 7:41pm UTC](http://discussions.gridprotectionalliance.org/t/disablerealtimedata-and-enablerealtimedata-commands/1307/2 "2024-09-10T19:41:40Z")

</div>

Hi Flor,

Those commands are used as part of a typical connection sequence designed to make it easier to receive a configuration frame without interference from data packets.

1. Connection to the PMU/PDC is established
2. Send `DisableRealTimeData` so that you are no longer receiving data packets
3. Send `SendConfigurationFrame2` and wait until you receive the configuration frame in response
4. Send `EnableRealTimeData` to begin receiving data packets again

The most relevant setting on the openPDC side of this communication is the `Auto Start Data Channel` setting. If you check that checkbox, openPDC will ignore the commands and keep the data stream running constantly.

If you are wondering why the remote PDC is disconnecting and reconnecting, it may have to do with your `UDP Channel` configuration. It looks like TCP connections are coming from `10.123.0.225`, but the openPDC is sending data to `224.0.1.1`.

Thanks,  
Stephen

---

<div class="post-metadata">

**Author:** ![FlorianoTorres](http://discussions.gridprotectionalliance.org/letter_avatar_proxy/v4/letter/f/a5b964/32.png) [@FlorianoTorres](http://discussions.gridprotectionalliance.org/u/FlorianoTorres)\
**Post date:** [September 11, 2024, 11:27am UTC](http://discussions.gridprotectionalliance.org/t/disablerealtimedata-and-enablerealtimedata-commands/1307/3 "2024-09-11T11:27:28Z")

</div>

Hi Stephen.

Thank you for answering, it helped me a lot!  
Regarding the disconnecting and reconnecting situation, I forgot to complete the output stream configuration. Now it is streaming to the other PDC.

Flor.
